Saab 9-5

Since 1997 of release

Repair and car operation

Saab 9-5
+ Cars Saab 9-5
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
- Systems of cooling of the engine, heating, ventilation and air conditioning
   + System of cooling of the engine
   - Systems of heating, ventilation and air conditioning
      The general information
      Removal and installation of the block of management by system of ventilation from a heater and К/В, removal and installation of the broad valve
      Valve replacement отсечки a cooling liquid and it э/м the valve
      Removal and installation of the fan of a heater
      Removal and heat exchanger installation
      Removal, repair and compressor K/V installation
      Removal and installation of the gauge of temperature in salon
      Removal and installation of the step-by-step engine заслонки air and e/motor mixing заслонки an air circulation mode
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Systems of heating, ventilation and air conditioning

The general information

The description of systems

The design of systems of ventilation with a heater and К/В is presented on an illustration.

Design of system of ventilation with a heater and К/В

1 — Salonnyj the filter
2 — the Additional filter (at a corresponding complete set)
3 — the heater Fan
4 — the Heat exchanger
5 — Zaslonka of a mode of air circulation
6 — Zaslonka of mixing of air

7 — air Distributor
8 — the Evaporator (models with К/В)
9 — the Broad valve (models
With К/В)
10 — the Circulating pump (models V6 for the markets with a frigid climate)
11 — the Valve отсечки waters

The salon is divided on two zones, – the driver and passengers, – for each of which it is possible to establish individual parametres of ventilation, heating and an air conditioning, except a circulation mode. Management of system of ventilation with a heater and К/В is resulted in the Head Controls and operation receptions.

Hot ОЖ it is passed through the heat exchanger, heating up air passing through it. Air giving in salon is regulated заслонками. If to include the heater fan, air will move in salon more intensively. The fan can work with different speed. At closed заслонке ОЖ arrives on a small contour back in a contour of a radiator of the engine.

Before getting to salon, air passes through the filter in which the basic share of a dust settles. It is necessary to observe periodicity of replacement of the filter since the dusty filter limits air giving that will lead to a stagnation of air in salon. In addition the coal filter clearing air from final gases of diesel engines, etc. can be established

Distribution of streams of air of system of ventilation is carried out also with the help заслонок. On all models the air circulation mode is provided.

Air leaves salon through two ventilating apertures, located in a back part of the car.

Air central air (К/В) enters into a standard complete set of some models, and on other models can be established in addition. Besides, the system of automatic control by a heater and К/В (ACC) can be established. System ACC components are specified in illustrations.

Arrangement of components of system ACC

1 — the Block of management ACC
2 — the Gauge of temperature of air in salon
3, 4 — the Gauge of temperature of mixed air of models with the left/right wheel
5 — the sun Gauge
6 — the Step-by-step engine заслонки air distributions
7, 8 — the Step-by-step engine of mixing of air of models with the left/right wheel

9 — the Block of management of the fan
10 — Privodnoj the e/motor заслонки a circulation mode
11 — the Valve отсечки the heat exchanger
12 — the Circulating pump (models V6 for the markets with a frigid climate)

Works with system K/V should be carried out in a specialised workshop. Do not open a contour of circulation of a coolant as at contact with a skin the coolant can cause обморожение.

By means of system K/V air temperature in salon can be lowered concerning external temperature. At work of system humidity of air in salon decreases. In the crude weather, arriving fresh air preliminary it is cooled, then again heats up to the set temperature. Thus its drainage is made. By means of this procedure it is possible to get rid from запотевания glasses.

Components of system K/V and their arrangement are specified in illustrations.

Arrangement of components of system K/V

1 — the Compressor
2 — the Condenser
3 — the pressure Gauge
4 — the Receiver

5 — the Broad valve
6 — the Heater
7 — the Gauge of temperature of the evaporator
8 — Relay K/V

In system the coolant (type R134а) which depending on temperature and pressure can be in liquid or a gaseous state circulates. The schematical description of streams of a coolant is resulted on an illustration.

Coolant streams in system K/V

1 — the Compressor
2 — the Condenser
3 — the Receiver

4 — the Broad valve
5 — the Evaporator

The conditioner compressor is resulted by a belt from a cranked shaft of the engine. He creates pressure in a contour of the coolant representing gas, and causes its heating. In конденсаторехладагент it is cooled by external air. Thereof разогретый the coolant passes in a liquid phase. Then under a high pressure the coolant is passed through the broad valve therefore pressure of a coolant falls. After that the coolant evaporates in a contour, simultaneously strongly being cooled. In the evaporator the coolant selects heat from air blown through it. Thereof air is cooled and arrives in car salon. As a result of heating in the evaporator the coolant turns to gas and under low pressure arrives in the compressor then circulation process repeats.

Design of the broad valve

1 — Gazonapolnennaja the chamber
2 — the Diaphragm
3 — Press a rod
4 — the Ball

5 — the Spring
6 — the Party of low pressure
7 — the high pressure Party

On model with diesel engine V6 the additional heater working on diesel fuel can be established. Besides, for increase in a water stream through a radiator of a heater of the models delivered on the markets with a frigid climate, the circulating pump (the Design of system of ventilation with a heater and К/В see an illustration) can be established.

Design of an additional heater

1 — the heater Fan
2 — the E/motor of the fan of a heater
3 — the Heat exchanger
4 — the combustion Chamber
5 — the Candle накаливания
6 — the ignition Gauge
7, 8 — the Gauge of temperature ОЖ 1, 2
9 — the management Module

10 — the Air inlet
11 — the Exhaust pipe
12 — the Fuel pump
13 — the Fuel filter
14 — the Safety lock
15 — 8-kontantnyj a socket
16 — Inlet branch pipe ОЖ
17 — Final branch pipe ОЖ

Security measures at system K/V service

System K/V should be served by exclusively prepared technicians trained in safe working methods with application of the appropriate equipment and with observance of rules of depressurization, and also acquainted with receptions of gathering and storage of an automobile coolant.

    Do not suppose contact of a coolant to a skin; At work near to system K/V put on goggles; At coolant hit on a skin or in eyes do not pound the amazed place. Immediately wash out the amazed site cold water within not less than 15 minutes. Immediately address for medical aid in a medical institution. Self-treatment is not supposed; The coolant is stored in a new cylinder under pressure. Store a cylinder at temperature not above +50 hailstones. Take the measures excluding falling of a cylinder from height or other situations which can lead to its damage; Works should be spent in well aired premise. The coolant quickly evaporates, leads to reduction of access of oxygen and the complicated breath; The gaseous coolant is heavier than air and rather quickly should gather below, for example, under the car; At coolant combustion poisonous gas is formed. Store a coolant far from open sources of fire. Do not smoke at work with system K/V; At carrying out of welding works near to system K/V do not subject to its influence of a heat or an open flame. The overheat can lead to pressure increase in system and to ignition; Clearing of the condenser or the evaporator by means of water steam is not supposed. It is necessary to use only cold water or compressed air.