Saab 9-5

Since 1997 of release

Repair and car operation

Saab 9-5
+ Cars Saab 9-5
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
- Automatic transmission
   The general information
   Search of malfunctions - the general information
   Removal and installation of assemblage of the lever of the selector of modes АТ and its casing
   Removal, installation and adjustment of a cable of the selector of modes АТ
   Removal and installation of the lever of the selector of modes АТ and dismantling of its casing
   Removal and installation э/м valves AT, their case and its cover
   Removal and installation of gauges of speed
   Removal and installation of hydraulic lines АТ
   Removal and installation TCM
   Replacement and adjustment of the gauge of position of the selector of modes АТ
   Removal and installation АТ
   Replacement of epiploons of power shafts
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation АТ


    Lay on wings protective covers and remove the top cover of the engine. Remove the storage battery together with the pallet. Remove the assembly block of the relay and safety locks and remove it aside. Separate the sockets fixed in holders.
    Remove with АТ a ventilating hose (6), establish the lever of the selector (7) on АТ in position L and remove it.
    Remove a clamp and take a cable of a drive of the lever of selector AT from an arm (8). On 6-cylinder models disconnect the cable channel (9) from the power unit. Turn out 3 top bolts (10) fastenings АТ, clear area round a joint of a jellied tube with АТ and lift the receiver (11 and 12).
    Separate a socket () a ljambda-probe (ов) (13), give a nut (14) fastenings of a back support of the engine and bolts (15) fastenings of a back pillow of the engine

Bolts completely do not turn out.

    Hang out the power unit and lift the car. Remove forward wheels, the bottom protective casings of an impellent compartment and forward section of final system.
    Turn out bolts (22) fastenings of the steering mechanism, remove two back collars (23) fastenings of submitting tube ГУР to a stretcher and remove tubes К/В from plastic collars on a stretcher.
    Remove the case of an air cleaner (24). On 4-cylinder models disconnect a radiator from интеркулера (25). From both parties of the car give bolts of fastening of spherical support of a suspension bracket to rotary fists and bolts of racks of the stabilizer of a suspension bracket (36).
    Remove a forward support of the power unit and basic plates (29).
    Establish under a stretcher the special stand and give the remained 4 bolts (32) fastenings of a stretcher. Lower a stretcher at the stand approximately on 5 sm that it was possible to remove two forward collars of fastening of submitting tubes ГУР. Remove collars, lower the stand together with a stretcher and take him aside. Remove a back support and a pillow of the engine (34). On 4-cylinder models remove the plate fixed by two bolts to get access to hydrotransformer fastening on приводном a disk. On 6-cylinder models remove a stopper (under a starter), closing bolts of the hydrotransformer (35).
    Turn out 6 bolts of fastening of the hydrotransformer to приводному to a disk, turning for this purpose a cranked shaft (36).
    Wring out the hydrotransformer from transmission and fix it in this position by means of the special adaptation (37) for the period of removal АТ. Remove the components specified in illustrations. Empty АТ. Take from АТ the left power shaft, suspend it on a plait and lower the car. Remove the left pillow of the engine. Lower the power unit approximately on 10 sm that АТ it was released from a constructive element. Lift the car. Fix on a jack the special adaptation, level its centre with centre AT and with its interfaced surface (see an illustration).
    Turn out the remained bolts of fastening АТ to двигател, separate them and remove АТ from the special adaptation.
    Installation is made upside-down.