Saab 9-5
+ Cars Saab 9-5
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
- The power supply system and release of the fulfilled gases
The general data and security measures
Sbrasyvanie pressure in fuel system
- The power supply system of petrol engines
Principle of functioning of a control system of fuel injection
Removal and installation of a sleeve of an air inlet and the case of the air filter
Removal and installation of gauges MAF, MAP, IAT and the gauge of temperature/pressure of air of pressurisation
Removal and installation of a tube of forced air
Removal and installation of the case of a throttle
Removal and installation of the control valve of forced air
Removal and installation перепускного the valve турбокомпрессора
Removal and installation турбокомпрессора
Removal and installation интеркулера
Removal and installation of a pedal of gas, adjustment of a cable of a drive throttle заслонки
Removal and installation of a fuel tank
Replacement of the fuel filter
Removal and installation of assemblage of the fuel pump and the gauge of a stock of fuel
Removal and installation of a fuel distributive highway and injectors
Removal and installation of a regulator of pressure of fuel
+ The power supply system of diesel engine V6
+ Systems of release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of the case of a throttle
|
|
Switch off ignition and remove the top cover of the engine.
Uncover a broad tank of system of cooling to dump pressure in system, and establish a cover into place.
|
|
4-cylinder engines
|
|
|
|
Uncover the lever of a drive throttle заслонки.
|
Press together two hoses of system the coolings going to the case of a throttle.
|
|
Remove a hose перепускного the valve of forced air, and also two hoses of preliminary warming up (6 on an illustration). Disconnect the bottom vacuum hose (7).
|
Lift the receiver forced air (see Has undressed Removal and installation of a tube of forced air).
|
|
Disconnect a cable of a pedal of gas from the lever of a drive throttle заслонки (10 on an illustration).
|
Remove a rubber protective cap and separate a socket э/м the emergency operation valve (11 on an illustration). Separate also a 10-contact socket of the case of a throttle (12).
Turn out 3 bolts of fastening of the case of a throttle (13 on an illustration), raise it and disconnect a hose under э/м the emergency operation valve.
Installation is made upside-down. If necessary use new consolidations.
After engine start make sure of reliability of a tightening of all connections.
|
|
Engine V6
|
|
Disconnect from the case of a throttle a tube of forced air (see Has undressed Removal and installation of a tube of forced air).
|
|
Press two hoses of system the coolings going to the case of a throttle (5 on an illustration).
|
Disconnect a cable (6 on an illustration) pedals of gas from the lever of a drive throttle заслонки.
Separate a socket э/м the emergency operation valve (7 on an illustration) and a 10-contact socket of the case of a throttle (8).
Disconnect a vacuum hose and ослабьте connection of a line of a purge under э/м the emergency operation valve (9 on an illustration).
Disconnect from the case of a throttle two hoses of system of cooling (10 on an illustration).
|
|
Turn out 3 bolts of fastening of the case of a throttle and remove it.
|
Lift the receiver forced air (see Has undressed Removal and installation of a tube of forced air).
Item 8-9 (4-cylinder engines) see.
|
|
|
|