Saab 9-5
+ Cars Saab 9-5
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ The power supply system and release of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
- The external equipment and кузовные elements
Removal and installation of bumpers
Removal and installation of decorative lattices of a radiator
Removal and installation of spoilers
Removal and installation of a covering and the decorative panel of a cover of a luggage carrier
Removal and installation локеров wheel arches
Removal and installation of forward wings and обтекателя a windscreen
Removal and installation of beams of the top luggage carrier of models the Versatile person
Removal and installation of assemblage of the top hatch and its components
Removal and installation of a cowl and its lock
Removal, installation, dismantling and assemblage of a forward door and its components
Removal, installation, dismantling and assemblage of a back door and its components
Removal, dismantling, assemblage and installation of a door of a back and its components
Removal and installation of a cover of a luggage carrier and its components
The fixed glasses
+ The salon equipment
+ Onboard electric equipment
|
Removal, dismantling, assemblage and installation of a door of a back and its components Removal, installation and door adjustment
|
|
|
|
Open a door of a back and remove casings from its loops.
|
|
|
Remove the top cover of glass, a covering of rack D and a ceiling, holders of a grid for fixing of cargoes, and also clamps and covers between racks C and D.
|
|
|
A little start up a covering of a ceiling and separate electroconducting and tube sockets стеклоомывателя (5). On both parties open cable channels (6) and remove them from electroconducting plaits.
|
|
|
Deduce electroconducting through loops (7), ask the assistant to keep a door and turn out 4 bolts (9) its fastenings to loops.
|
Remove a door from loops.
Installation is made upside-down. After installation adjust position of a door concerning a body.
Adjustment of position of a door in to the left-to the right and forward-back is made at the released bolts (9) fastenings of a door to loops. For adjustment of position of a door upwards-downwards execute the actions described more low.
|
|
Remove a lateral emphasis, consolidation and doorway furnish.
|
Remove the components specified in paragraph 2 and slightly lower a ceiling covering.
|
|
Adjust door position, having released on 3 bolts on each loop (8).
|
Tighten bolts and establish acting in film components.
|
|
The internal handle and door covering
|
|
Open a back door.
|
|
Remove a framework (2) round the internal handle, having unbent its screw-driver in three 3 cuts, and having pulled downwards at the released clamps.
|
Liberate a covering of a door from clamps (3).
|
|
Remove a covering. For this purpose at first pull downwards to it the top part, and then pull back.
|
|
|
Remove two draughts of the lock (5), turn out screws (6), shift the handle aside and remove it (7).
|
|
|
The lock and the lock cylinder
|
|
|
|
For removal of the cylinder of the lock give nuts, unhook draught (5) and separate a socket.
|
|
|
For lock removal disconnect 3 draughts (5), turn out 4 bolts (6) and separate a socket (7).
|
|
|
The external handle
|
|
|
|
Turn out screws outside of a door.
|
|
|
Remove both back combined lanterns and licence plate (6) plate.
|
Turn out nuts (7), remove draught and separate a socket (7).
|
|
Liberate clamps and remove the lock together with licence plate illumination.
|
|
|
|
|