Saab 9-5

Since 1997 of release

Repair and car operation



Saab 9-5
+ Cars Saab 9-5
+ Controls and operation receptions
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
- The power supply system and release of the fulfilled gases
   The general data and security measures
   Sbrasyvanie pressure in fuel system
   - The power supply system of petrol engines
      Principle of functioning of a control system of fuel injection
      Removal and installation of a sleeve of an air inlet and the case of the air filter
      Removal and installation of gauges MAF, MAP, IAT and the gauge of temperature/pressure of air of pressurisation
      Removal and installation of a tube of forced air
      Removal and installation of the case of a throttle
      Removal and installation of the control valve of forced air
      Removal and installation перепускного the valve турбокомпрессора
      Removal and installation турбокомпрессора
      Removal and installation интеркулера
      Removal and installation of a pedal of gas, adjustment of a cable of a drive throttle заслонки
      Removal and installation of a fuel tank
      Replacement of the fuel filter
      Removal and installation of assemblage of the fuel pump and the gauge of a stock of fuel
      Removal and installation of a fuel distributive highway and injectors
      Removal and installation of a regulator of pressure of fuel
   + The power supply system of diesel engine V6
   + Systems of release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation турбокомпрессора

4-cylinder engines

 PERFORMANCE ORDER

  1. Dump pressure in system of cooling and поддомкратьте the car.
  2. Remove the bottom forward protective casing of the engine and empty cooling system.
  1. Remove an arm (5 on an illustration) fastenings турбокомпрессора, ослабьте a nipple of return of oil and connection of a tube (6) from турбокомпрессора to the block of cylinders. Закупорьте an aperture in the block of cylinders.
  1. Disconnect from турбокомпрессора an oil tube (7 on an illustration), going from the case of the oil filter. Lower the car on the earth.
  1. Remove перепускную a tube (9 on an illustration) and the valve, separate sockets of the control valve (10) and gauge MAF (11) and disconnect hoses турбокомпрессора and cases of a diaphragm (12).
  1. Turn out a hollow bolt of a tube (13 on an illustration) ventilation картера from a sleeve of an air inlet and a bolt from a cover of a head of cylinders. Postpone a tube and electroconducting aside.
  2. Remove an elevating eye of the engine (15 on an illustration), gauge MAF and an air line (16).
  1. Remove a thermofilter of a final collector (17 on an illustration) and ослабьте quick disconnect connection of a ventilating hose (18).
  1. Loosen the V-shaped (19 on an illustration) a collar of a sleeve of an air inlet on турбокомпрессоре also remove a sleeve (20).
  2. Loosen the a collar (21 on an illustration) hose fastenings интеркулера to турбокомпрессору also close a hose from a dust.
  3. Disconnect from турбокомпрессора forward section of final system and accurately lower it (22 and 23 on an illustration).

Than 5 hailstones are not supposed to reject forward section of final system on a corner more.


  1. Disconnect an oil tube (24 on an illustration) from the case of the oil filter and collect copper washers.
  1. Disconnect a tube of cooling from турбокомпрессора (25 on an illustration) then turn out a bolt of fastening of a tube to the water pump (26).
  2. Disconnect a returnable water tube from a head of cylinders, and also from an arm of the gauge of pressure then turn out a bolt of fastening of a returnable tube to турбокомпрессору (27 and 28 on an illustration).
  3. Give nuts (29 on an illustration) fastenings турбокомпрессора to a final collector and remove турбокомпрессор.
  4. Installation is made upside-down. Pay attention to following moments:
    • Preliminary make sure that bearings турбокомпрессора are filled by oil. If necessary fill oil through submitting tube турбокомпрессора and turn his hand on enough of turns;
    • Grease fastening hairpins турбокомпрессора with greasing Molycote 1000;
    • At first tighten only the top gangs of fastening турбокомпрессора. The bottom nut should be tightened only before it is necessary to connect to турбокомпрессору an oil tube;
    • Use new sealing rings.

Engine V6

 PERFORMANCE ORDER

  1. Tyre out the car on the lift and remove the top cover of the engine.
  2. Remove a hose of forced air together m перепускной a tube and the valve.
  3. Close a final aperture интеркулера.
  1. Remove a thermofilter of a final collector (5 on an illustration).
  1. Lift the receiver ventilation картера between an inlet tube турбокомпрессора and a head of cylinders (6 on an illustration), and also a hose from an oil separator. Take a hose aside.
  2. Remove submitting tube турбокомпрессора (7 on an illustration) and take her aside.
  3. Disconnect a final hose турбокомпрессора, going to интеркулеру (8 on an illustration).
  4. Remove assemblage of fans of a radiator (see the Head of System of cooling of the engine, heating, ventilation and an air conditioning).
  1. Press submitting and returnable hoses of cooling турбокомпрессора and disconnect them from it (10 and 11 on an illustration).
  1. Remove directing щупа level of impellent oil (12 on an illustration) and disconnect from турбокомпрессора a forward hose (13).
  2. Separate a socket of a ljambda-probe and поддомкратьте the car.
  3. Remove a coupler of electroconducting of a ljambda-probe, preliminary having remembered a line of a lining of electroconducting. Lower electroconducting.
  4. Separate forward and back sections of an exhaust pipe, then disconnect forward section from a final collector and remove it.
  1. Remove a returnable oil tube (19 on an illustration) турбокомпрессора and its arm (20).
  1. Disconnect an oil tube from the case of the oil filter (21 on an illustration).
  2. Lower the car on the earth and give nuts of fastening of assemblage of a forward final collector with турбокомпрессором.
  3. Installation is made upside-down. Use new linings and sealing rings.